13559553569

用途：用于橡膠出片冷卻把水吹幹。

特點: 本機采用強力風機根據風刀角度把膠片吹幹。

主要技術參數 technical parameters
型号 model	lj-1200
外型尺寸appearance size: l*w*h(mm)	1200*950*1430
工作寬度working width(mm)	600
風刀功率power (kw)	5.5
輸送功率power (kw)	0.75
重量weight(kg)	300

使用說明

公共設備電力：電壓380v,50hz。

主電源線：4平  四芯線

1、 機械運轉中手切勿接觸滾輪。

2、 橡膠片應該保持平整進料，防止卡料。

3、 進料膠片厚薄要一緻且要平整進入膠輥，太簿的膠片進膠棍必需折成雙層，噴水量要夠多，彈簧（進料膠棍）不要調整過緊，工人的操作速度快，以免卷料。

4、 以上操作失誤，如有卷料，清理時，刀片一定不要損傷膠輥。

5、 後面出料膠輥進料時，簿料必需折成雙層稍微一點拉力。不緻于卷料，仍有存大阻料，查彈簧是否調整不當，查膠輥是否卡住，上面膠輥和下面膠輥是否緊貼，軸承是否沒換油卡死，鏈條是否過松等。6、 壓水不幹，煉膠機上要裝齊邊刀，減少碎料，平整一緻，調整膠輥彈簧，注意彈簧不要調死，以免損壞電機。

7、 膠片如兩邊跑動，請調整膠輥兩端彈簧壓力一緻。

8、 機台工作時，手一定不要伸進裏面，如有問題，一定要停機解決。

9、 滾輪工作時旋轉不正常，請檢查鏈條松緊情況，齒輪是否損壞。

10、  發現電機有異聲，要停機檢查，鏈條皮帶松動要及時調整，螺絲松動要及時緊固。

11、 如風刀出風量小，查看過濾網是否灰塵過多堵塞，清洗過濾網。

rubber water cooling machine:

purpose: used for rubber sheet cooling to dry the water.

specialty: the machine uses a strong fan to dry the film according to the angle of the blade.

主要技術參數 technical parameters
型号 model	lj-1200
外型尺寸appearance size: l*w*h(mm)	1200*950*1430
工作寬度working width(mm)	600
風刀功率power (kw)	5.5
輸送功率power (kw)	0.75
重量weight(kg)	300

instructions:

public equipment：power: 380v,50hz.

host power line:  4mm² four-core

1. do not touch the cutter die and roller during the operation of the machine.

2. rubber sheet should be kept flat to prevent material from sticking.

3. the thickness of feeding rubber slices must be consistent and the rubber slices should enter in the same level. too thin rubber slices should enter in a way of double-decker. water them with enough volume; do not adjust the spring too tight. the operating speed must be fast enough to avoid material rolling.

4. if above operational errors occur and material rolled, don’t let the blade operate the rubber roller when cleaning up.

5. when the triple-rubber-roller is feeding material, thin one must be folded into double-decker. if there still exist non-smoothly feeding, check whether the spring is adjusted properly; or check whether the rubber roller is blocked;

check whether the upper rubber roller is stuck with the lower one; or  check whether the bearing roller is blocked for without oil replacing ;or check whether the chain is too loose, etc .

6. pressurized water quit ,the knives should be installed in a level to the rubber making machine . reduce rubber oddments and make rubber in a level and in the same thickness. do adjust the spring, but not too tight to avoid damaging the mortor.

7. rubber out of the sheet partial movement, please adjust the cots at both ends of the spring pressure consistent.

8. do stop the machine when there is problem. do not put hands in when the machine is still working.

9. the roller does not rotate properly when working. please check the tightness of the chain and whether the gear is damaged.

10. any unusual voice, stop and check. adjust chains and screws if they are loose.

11. if the air output of the air knife is small, check whether the filter is clogged with too much dust and clean the filter.